Fashion Dot LINK IN

How To Take Blouse Measurement From Customers

Computerized Blouse Cutting - www.fashiondot.in

Method To Take Measurement From the Customer

1. HEIGHT A
    This measurement should be taken from the customer at the back side. First correct the customer blouse without any wrinkles now take the measurement from the shoulder top to their blouse. Height don't leave any folding cap for stitching gap height = 13”.

While Taking Measurement, Extent The Blouse Height From Their Blouse Height From .5 Inch. Or
Extend The Height From Min 1inch To 1.5 Inch From Their Brasier Height. The Average Height For The
Customers Will Be From 12inch To 14.5 Inches, Based Upon The Customer Height. If The Customer
Height Exceeds From 14.5 Inch, The Front Patti Height Will Be Large, Then The Patti Will Bound To The
Customers Stomach, So The Patti Will Be Fold, So Please Check With The Above Measurement.

Computerized Blouse Cutting - www.fashiondot.in
2. SECOND BODY LOOSE B
      This should be taken from the customer's upper part of the chest. No loose should be leave on the tape, check the back side that tape is not in crosses. Take the measurement as round number like 32, 33, and 34. The measurement should not like ¼ ½ ¾. 

Don’t Let Loose In The Body Loose While Taking The Measurement,
For Ordinary Blouse (Without Lining) -30inch - 24 Hours Blouse
For Executive And Lining Blouse - 31 Inch – 10 Hours Blouse
For Function Wear Blouse – Reduce ½ Inch In Middle Hand Loose – 2 Hours Blouse

3. SHOULDER FINISHING D
    This should be taken from the customers blouse from the sleeve joint part to the next side finishing. This measurement will be like 2, 2 ¼, 2 ½. EXAMPLE = 2 ½” 

Check The Below Measurements By Using The Customer Body Measurement. Customer
Shoulder Finishing Measurement Can Be Plus Or Minus 0.25 Inch From The Below Measurement.
For Body Loose 26-30 = Shoulder Finishing 1.5 Inch
For Body Loose 31-36 = Shoulder Finishing 1.75 Inch;
For Body Loose 37-38= Shoulder Finishing 2 Inch;
For Body Loose 39-43= Shoulder Finishing 2.25 Inch;
For Body Loose 44-49= Shoulder Finishing 2.5 Inch.
Measurement Can Increase Or Decrease From .25 Inch From The Above Measurements. If This
Measurement Exceeds From The Above Rule, The Neck Width Will Be Less, So The Blouse Will Not Set Perfect.

Computerized Blouse Cutting - www.fashiondot.in
4. HAND HEIGHT E
      Hand height should be taken from the solder sleeve edge to their sleeve height requirement.
EXAMPLE = 5”

Sleeve Height Can Start From 4.5 Inch. If The Sleeve Height Below The 4.5 Inch, Then The
Sleeve Loose Should Add By .5 Inch. If The Sleeve Height Is Above 4.5 Inch, Then Take The Average Hand Loose Measurement.


5. HAND LOOSE F
       Hand loose should be taken from the customers where their sleeve height ends. Don't leave any loose. EXAMPLE = 12”

Take The Sleeve Loose As Per The Customer’s Measurement For Ordinary Blouses, For
Model Sleeves Like Cap Sleeve And Petal Sleeve Sleeve Loose Can Extend By .5 Inch.

Computerized Blouse Cutting - www.fashiondot.in
6. MIDDLE HAND LOOSE G
       This measurement should be taken in the customers middle hand part without leaving any loose. EXAMPLE = 12”

Take The Customer Measurement As Per The Middle Hand Loose. This Middle Hand Loose
Should Not Less From The Sleeve Loose, And Should Not Exceed From Above 1.5 Inch From Sleeve Loose. The Both Measurement Can Be Equal Also.

7.  FRONT NECK HEIGHT L
      This should be taken from the front side. The neck deep minimum should be 1/2 “down from their body armhole line. The tape should not taken by cross, it should be straight.
EXAMPLE = armhole 5 ½ + ½” = Total 6” Minimum neck height should be 6”.

Please Check the Front Neck Height Measurement with Customer’s Body Loose Measurement,
For Body Loose 26-30 = Front Neck Height 5.5 Inch
For Body Loose 31-36 = Front Neck Height 5.75 Inch;
For Body Loose 37-38 = Front Neck Height 6 Inch;
For Body Loose 39-43 = Front Neck Height 6.50 Inch;
For Body Loose 44-49 = Front Neck Height 6.75 Inch.
Measurement Can Increase Or Decrease From .50 Inch From The Above Measurements. If
This Measurement Exceeds From The Above Rule, The Neck Width Will Be Less, So The
Blouse Will Not Set Perfect.

Computerized Blouse Cutting - www.fashiondot.in
8. BACK NECK HEIGHT   M
       This should be taken from the back side. The neck deep minimum should be ½” down from their body armhole line. The tape should not taken by cross, it should be straight.
EXAMPLE = armhole 5 ½” + ½ =   Total 6”  Minimum neck height should be 6”.

Back Neck Height Can Be Down From Minimum .5 Inch From The Front Neck Height. The
Measurements Can Be Changed according To the Customer’s Choice.

9. HIP LOOSE  O
                  This should be taken from the front side where the last hook will be hanging. This measurement should be taken very tightly with the customer. While taking this measurement, Customer will tell no need of this much tight but for perfect blouse the measurement should be taken like this tight only. EXAMPLE = 29”

Hip Loose Can Be Less From 4 Inch Upto 10 Inch From The Body Loose Measurement.
Example – Body Loose-40= Hip Loose May Be = 36-30, Hip Loose Should Not Be 29 To 37.

10. FRONT POINT CENTER  U
        This measurement should be taken from the front side from the top of the shoulder to their front point center, this measurement should be very accurate. EXAMPLE = 9”

If The Customer’s Blouse Leaves The Point Center Sharp, Less The Front Point Center Height Or If
The Customer Does Not Require Sharp, Less The Front Dot Height Measurement By 1”.

 Sample Blouse Measurement Chart

 

Send your Measurement, you can your Size Blouse Computer drawing to your mail.

Thank you

In my Next Post I will  Explain how Cut The Back Part Of The Perfect Blouse.

Designer Chudi ( Salwar) Model - 01

Fashion Dot Software